That's what I want it for bugs and little rocks from the road. Q: From all the reviews, many people used it on their cars. Q: Can this product be used on the front of a car? For one coat, a 16 fl oz bottle should cover: Q: how far will a16oz bottle go i have 1 Cadillac Escalade 2 jet ski and a22ft fiber glass boatĪ: The RejeX film is very thin (less than a micron), so a little goes a very long way. RejeX is wiped on, allowed to dry to a haze for approximately 20 minutes, wiped off, then allowed to cure for 8-12 hours (depending on the humidity the higher the humidity, the faster the cure). Q: Can this product be applied with my orbital BufferĪ: That is not recommended. RejeX Polymer Coating (16 oz.) - So Slick, Bugs Can't Stick! Overview: Polishing compounds and solids from the product so it would be safe and Is RejeX safe to use on aircraft windshields? RejeX application and the time saved in keeping your vehicles clean, RejeX isĪlso an outstanding value. When you factor in the cost of applying wax several times compared to a single ![]() Longer, makes your airplane easier to clean and provides superior protection. RejeX is easier to apply than waxes, lasts much Leaves, and once they see how much easier it is to apply than waxes, they often However, once they see the deep, lustrous finish RejeX Many people start using RejeX on the leading edges of aircraft to makeīug removal easier. Should I just put RejeX on the leading edges of my airplane, or should RejeX leaves a shinier, longer-lasting finish than wax… and the wax can't adhere However, the duration of protection will be reduced as the softer underlying waxĭegrades comparatively quickly. RejeX is not meant to be used on porous surfaces, highly oxidized painted Glossy plastic and polished metal surfaces. Protects and beautifies painted metal, glass, acrylic, gel coat, fiberglass, That are known to contaminate paint and cause problems when repainting. RejeX contains none of the free silicone oils found in some other products It's easy to apply and producesĪ deep, lustrous shine that outlasts the most popular waxes by months. It also makes graffiti easy to removeĪnd can be applied to windshields to repel rain. This very thin film - less than a micron thick - prevents stains andĪdhesion of common contaminants such as exhaust, bugs, oil, tree sap, birdĭroppings, road grime, brake dust, etc. RejeX is a thin-film polymer coating designed to provide a high-release before it has cured, the contaminants may interfere with or imbed in the protective film.RejeX was originally developed for the Air Force to keep turbine exhaust gas If the coating is exposed to contaminants such as oil, fuel, soot, hard water, tree sap, cleaners, etc. It is important to allow RejeX to cure for 8-12 hours after the haze has been wiped off. Curing is required to allow the monomers (polymer building blocks) that make up RejeX to attach to the surface being treated and to crosslink into a crystal-clear, impervious film. If the surface is too hot, the coating can cure before it has properly bonded to the surface, so it may not perform up to its potential. When over 85° F, be sure to apply RejeX out of direct sunlight. Ideally, RejeX should be applied to a cool, dry, clean surface. RejeX contains none of the free silicone oils found in some other products that are known to contaminate paint and cause problems when repainting. It’s easy to apply and produces a deep, lustrous shine that outlasts the most popular waxes by months. It also makes graffiti easy to remove and can be applied to windshields to repel rain. This very thin film – less than a micron thick – prevents stains and adhesion of common contaminants such as exhaust, bugs, oil, tree sap, bird droppings, road grime, brake dust, etc. ![]() RejeX is a thin-film polymer coating designed to provide a high-release protective finish for vehicles of all kinds. The amazing polymer finish that "rejects" UV, bird droppings, bugs splats, brake dust and other contaminants and road grime.
0 Comments
Leave a Reply. |